Home › Blog › Water Heater Not Heating
No hot water

Water Heater Not Heating: What to Check First

Cold showers are miserable, and the cause is often simple. This guide shows what to check when your water heater is not heating, for both gas and electric tanks, and when to call for help.

Plumber repairing copper supply lines at a Northbrook, Illinois home(847) 860-7173Call to confirm availability
First checks

Start With the Easy Things

Before you assume the worst, check the basics. Make sure the power or gas is on, the thermostat is set properly and no breaker has tripped. A surprising number of cold water calls end with a reset button or a pilot relight.

  • Check the breaker for an electric heater
  • Confirm the gas valve is on for a gas heater
  • Look at the thermostat setting, ideally around 120 degrees Fahrenheit
  • Press the reset button on electric models once
  • Check whether other fixtures also lack hot water
Safety

Turn off the power or gas before opening any panel. If you smell gas, leave the home and call your gas utility immediately.

Electric heaters

Electric Heater Troubleshooting

Electric tanks use two heating elements and two thermostats. If one fails, you may get lukewarm water or only a small supply of hot water. The high limit reset button may also trip when the tank overheats.

SymptomLikely causeFix
No hot water at allTripped breaker or failed upper elementReset breaker, test elements
Lukewarm waterFailed lower elementReplace the element
Hot water runs out fastSediment or failed lower elementFlush the tank, test elements
Reset trips repeatedlyThermostat or wiring issueCall a plumber
Gas heaters

Gas Heater Troubleshooting

On gas heaters, the pilot light or igniter may go out because of a draft, a failed thermocouple or a dirty burner. Many modern units have an electronic ignition and show an error code. Check your manual for relight steps, and stop if the flame will not stay lit.

SymptomLikely causeFix
Pilot light is outDraft or failed thermocoupleRelight or replace the part
Burner will not stay litDirty burner or bad thermocoupleClean or replace
No hot water and error codeIgnition or sensor faultCheck the code in the manual
Pilot and burner lit but little hot waterSediment or thermostat issueFlush and test

If the unit is not responding to a relight, the safest option is to call a plumber.

Sediment

Why Sediment Matters

Minerals settle at the bottom of the tank and insulate the water from the burner or lower element. A tank full of sediment heats slowly and makes rumbling noises. Flushing the tank may restore performance, but a very old unit may already be damaged.

Rumbling sounds

Steam bubbles trapped under sediment.

Rusty water

Tank or anode rod corrosion.

Long recovery time

Scale on the burner or element.

Lower capacity

Sediment takes up space in the tank.

Other causes

Mixing Valves, Dip Tubes and Plumbing Issues

A failed dip tube can send cold water to the top of the tank so hot water cools quickly. A faulty mixing valve or crossover plumbing issue can also create lukewarm water at certain fixtures. If hot water is weak at only one faucet, the problem may be in that faucet rather than the heater.

  • Check hot water at multiple fixtures
  • Look for leaks at the tank and connections
  • Check if the heater is too small for the household
  • Make sure the shutoff valve is fully open
  • Listen for hissing or popping from the tank
Repair or replace

Knowing When It Is Time to Replace

A heater under ten years old is often worth repairing. A tank that leaks, rusts or needs repeated service is usually better replaced. Our water heater repair team can test elements, thermostats and gas controls and advise on the best choice.

SituationUsually best
Single failed element or thermostatRepair
Tank leaking from the shellReplace
Heater 12+ years old with repeated issuesReplace
Pilot or thermocouple failure on a newer unitRepair
Prevent

Keeping Hot Water Reliable

  • Flush the tank annually
  • Test the pressure relief valve once a year
  • Replace the anode rod when worn
  • Keep the area around the heater clear
  • Schedule a plumbing inspection if the heater is over ten years old
Good habit

Write the install date on the tank with a marker. It makes future decisions easier.

Reading signs

What Your Heater Is Telling You

A water heater not heating usually gives clues before it stops completely. Strange noises, slow recovery and lukewarm showers are signs that parts are wearing. Paying attention to these signals lets you repair a small issue instead of waiting for a cold shower and a possible leak.

ClueWhat it suggestsNext step
Lukewarm waterFailed element or thermostatTest and replace the part
Popping or rumblingSediment buildupFlush the tank
Water too hotThermostat set too high or faultyLower the setting and test
Short hot showersSediment or undersized tankFlush and check size
Rotten egg smellAnode rod reactionHave a plumber inspect
Do not wait

If you see water at the base of the tank, shut off the supply and power and call for service right away.

  • Note when problems began
  • Check whether others in the home noticed
  • Keep a record of past service
  • Look for corrosion on fittings
Safety and efficiency

Settings That Save Energy and Prevent Problems

Set the thermostat around 120 degrees Fahrenheit for safety and efficiency. Higher settings raise scald risk and speed up scale buildup. If your household is large, consider whether the tank size matches your needs. A heater that struggles under heavy demand may simply be too small, not broken.

  • Keep the thermostat near 120 degrees Fahrenheit
  • Insulate hot water pipes near the heater
  • Consider a timer or smart control for electric units
  • Fix leaky hot faucets that waste heated water
  • Plan a replacement before the unit fails
Household sizeTypical tank size
1 to 2 people30 to 40 gallons
3 to 4 people40 to 50 gallons
5 or more people50 to 80 gallons
Comfort

Quick Workarounds Until Service Arrives

While you wait for a repair, take simple steps to stay comfortable. Heat water on the stove for dishes and use a shorter shower schedule. Keep the heater powered off if you suspect a leak or electrical issue, and leave panel covers on. Avoid running an electric heater with an empty tank.

  • Heat small amounts of water on the stove
  • Take quick showers when hot water returns
  • Keep children away from the heater
  • Do not bypass safety switches or valves
  • Take photos of any codes or labels for the technician
Be prepared

Have the model number and install date ready when you call. It speeds up the diagnosis and parts ordering.

Water Heater Questions

Why is my water heater not heating even though it has power?

A failed element, thermostat or sensor is often the cause.

How do I reset my electric water heater?

Turn off power, press the red reset button on the upper thermostat once and restore power.

Can I relight a gas pilot myself?

Yes, if the manual describes the steps and there is no gas smell.

Is a water heater not heating always an emergency?

It is urgent for comfort, but a leak or gas smell is a real emergency.

How much does repair cost?

It depends on the part and unit. A plumber can give a clear estimate after testing.

Need Help With a Plumbing Problem in Northbrook?

Call us and describe what is happening. We will explain the options and when we can visit.

Call (847) 860-7173
Call (847) 860-7173